Help on Tele2, tariffs, questions

A small piece of glass, a nail or an ordinary push pin lying under the table is enough to cause rubber boots into complete disrepair. The unpleasant surprise is aggravated by the fact that shoe repair shops Rubber boots are not accepted. Don't buy new boots. Let's try to figure out how to seal rubber boots with our own hands.

It is worth noting that rubber boots, like EVA boots, are not so easy to seal. Regular shoe glue won't take them, but superglue will ruin them.. You need special glue.

Angler's method

You can look for special rubber glue in hunting and fishing stores. The number of unsuccessful attempts will be reduced to a minimum if you know what your rubber boots are made of. To repair products made from PVC, polyurethane or EVA, completely different adhesives are required. Ask the seller for the glue you need and follow the instructions on the package. As a rule, the technology is the same: sand, degrease, glue a patch.

How to seal boots made of EVA, because they are porous? If you purchased special glue for EVA, then you won’t even need a patch. Carefully turn out the edges of the hole and apply glue to the porous structure until it is absorbed. Then line up the edges and press. After repair, even the boot will look quite aesthetically pleasing.

Cyclist's way

A proven way to reliably seal rubber boots is a bicycle repair kit. As a rule, it contains several patches per protective films, special glue and sandpaper. Rub the place where the patch is glued sandpaper, with an area slightly larger than the size of the patch. Then degrease it with acetone.

Remove the film from the patch and apply glue to the exposed surface, also cover the glued area on the boot with glue. After 5-10 minutes, when the glue has dried, press the patch firmly.

You can use repaired boots almost immediately, they will be completely sealed. One problem is that bicycle patches do not look very aesthetically pleasing, so they are only suitable for rubber country boots.

Motorist method

What to do if smart women's rubber boots need repair? Like EVA boots, they are best sealed without a patch. You can fill the hole in colored and transparent rubber boots with elastic adhesive sealant.

The adhesive sealant has proven itself well " crazy hands» brand "Done Deal". You can buy one in stores for car enthusiasts. For everything to work out as it should, do not neglect preparatory stages. After washing, dry the shoes thoroughly and degrease the hole with acetone. The quality of gluing depends on this.

Again, you also need rubber boots different glue- keep in mind that all of the listed materials are not suitable for leather.

Rubber shoes are incredibly popular in the off-season. And in gardens it is much more convenient to water and weed the beds, because no dirt or moisture is scary. With proper care and choice of manufacturer, these shoes will last you for many years.

How and with what to seal rubber boots?

However, no one is immune from damage to even thick rubber. We offer two simple and available methods, how to seal rubber boots.

Caring for rubber boots

So that such a nuisance does not take you by surprise, you should properly care for your rubber shoes. After all, even very good producers They will not be able to guarantee the safety of your boots if they are not properly cared for.

First of all, let's learn how to clean properly. To wash rubber shoes, just take warm water, soft cloth and just a little glycerin. Then appearance the product will last for a long time. Don't forget to ventilate your boots well to avoid the development of fungus.

After cleaning or use in very rainy weather, never place shoes on a radiator, dryer or use a hair dryer. Dry only in a warm, dry place or in a warm wind. If you purchased a model with a light or white sole, a regular school eraser will help make it look brand new again.

How to seal rubber boots - the classic method

Even if you take very good care of your rubber shoes, sooner or later they may deteriorate. In such a situation, the question quite logically arises: is it possible to seal the rubber boots, or will you have to go to the store for a new pair?

There is no need to panic, because it is quite possible to seal such a product. You don't even have to seek help for repairs. From the materials and tools used, you will need glue, solvent, a patch (it is usually cut from old inner tubes from bicycles or strollers).

1. Shoes should be thoroughly washed and dried, as discussed in the rules for caring for rubber boots.
2. Cut the patch to size. In addition to bicycle tubes, old rubber boots are quite suitable.
3. Next, using a solvent, thoroughly degrease the surface of the shoe and the patch itself. Make sure that no pieces of cotton wool or threads from rags remain on the treated area.
4. To fix the patch we use Super Moment type rubber glue for rubber. If you wish, you can simply go to any nearest shoe repair shop and ask the master to sell you some special glue for a nominal fee.
5. First we apply glue to the shoes and the patch, let it sit for a while, then fix it. The exposure time is usually indicated on the tube.
6. To keep the patch as tight as possible, it is usually tapped a little with a hammer or something similar.

How to seal rubber boots - an alternative option

Sometimes the patch method is disappointing and you have to look for something else to seal your rubber boots with. If after a while you see that it was not possible to fill the hole, go to a sporting goods store. Many bicycle owners claim that more reliable way repair rubber boots; if they are torn, use a repair kit for bicycle tires.

Whatever method you choose, it is better to put on your boots after a day, when the glue has completely dried and set well.

Related articles:

EVA stands for ethylene vinyl acetate and is an environmentally friendly, durable, lightweight, resilient and elastic material. It does not absorb moisture and odors, is easy to clean, in most cases it is used in the production of shoes and has the disadvantage that it is not resistant to sharp tools; such shoes will be punctured or even cut by a knot if the step is unsuccessful.

Therefore, repair is enough actual question for EVA products. Universal adhesives won't fit.

How to seal PVC or EVA rubber boots at home

Boots made from EVA can only be sealed with specialized material.

Characteristics of the adhesive composition

Sneakers, boots or winter fishing boots made of EVA material will be properly sealed only with the same material, i.e. EVA glue.

Properties:

• waterproof;
• does not spread;
• is able to tightly connect gaps formed at the bend, as well as side and corner ones;
• the repaired area remains almost invisible;
• the product stays on the shoes for a long time, thanks to which the damaged area is protected from repeated damage;
• the composition is consumed sparingly, since the manufacturer recommends applying it thin layer(otherwise the polymerization process becomes more difficult);
• inexpensive, a 15 ml tube costs about 100-120 rubles;
• Shelf life is 24 months (2 years).

How to use correctly

The method of working with EVA is practically no different from the usual one, you just need to take into account that it is impossible to glue PVC products with the product.

Instructions for use:

1. Clean the areas to be joined and degrease with acetone. You can do without degreasing, but in any case, the areas to be glued must be clean and dry.
2. Expand or compress the damaged area so that the porous surface of the ethylene vinyl acetate (usually inner side product) ended up outside. This is important because the glossy outer surface does not adhere.
3. Apply adhesive material to the porous area of ​​the cut (tear) and leave for three to four minutes.
4. After this, bring the edges of the gap together and press them firmly together.
5. The final hardening of the product occurs after a day (24 hours).

In a similar way, you can repair, for example, Toptygin winter fishing boots. The manufacturer indicates how to use the glue correctly on the packaging of the composition. Follow the instructions and the cut will literally disappear from your shoes.

There is raw rubber and a vulcanizer, but this is for level areas. Better buy new boots

Tape up rubber boots theoretically possible with rubber glue :)

Why theoretically, and even in quotes? Because this is not so easy to do. The patch falls off very often. Shoe workshops are reluctant or do not accept rubber shoes for repairs at all. Some people advise going to a car repair shop - if you're lucky, they can also vulcanize your tires. But this option is also slowly but surely dying out, since vulcanization is rarely used to repair new types of tires.

So what to do?

One option that works is to use bicycle tire repair kit - repair kit for cameras. The price is not very expensive, very effective. The kit contains patches of several sizes, special glue and even, most often, a piece of sandpaper. There are usually instructions too.

• berm patch of suitable size
• clean the area with sandpaper (it’s better not to degrease, but if you want, then use acetone rather than gasoline)
• apply glue to the damaged area of ​​the boot
• remove the film from the patch and also apply glue on the side where the film was
• Let the glue dry slightly (about ten minutes) and press the patch to the boot.

It is better to wear it not on the same day, but only the next day.

This works if the hole is somewhere on the boot. What if it's on the sole? Then another tactic is needed. The fact is that the place that needs to be sealed must be even, smooth, and rubber boots usually have a fairly deep profile. But nothing is impossible - take a sharpening machine and process this place until it becomes smooth enough, and then glue it in exactly the same way as described above.

The only disadvantage of patches on the soles is that they will quickly wear out if you wear the boots often and on a hard, rough surface such as asphalt. But if boots are needed only occasionally and mainly for entering the water (fishing, for example), then they will last a little longer. If it gets worse again, the procedure will need to be repeated.

Rubber boots are essential footwear to wear in wet, rainy weather. And the trouble is if they were carried very little, but somewhere they were damaged and they let water through.



So how do you repair and seal rubber boots?

1. In order to prepare your boots for repair, you need to thoroughly wash and dry them. Make a patch from tires and stick it on the inside.
2. Another way is to use special glue. In order to find it, you can look into the hunters' store. In order to purchase a suitable adhesive composition, be sure to consult the seller in the store.
3. You can use glue-sealant, purchased at a car enthusiast store. We neutralize the gluing area and lubricate the torn edges with glue and press them together.



The approach to rubber materials is simple. First you need to take into account that the shoes must be dry. If there are any oily or greasy stains, then the surfaces to be glued must be degreased with acetone.

Apply a thin layer of glue to the surfaces, let it dry a little and firmly attach the surfaces to each other. You can use these small vices as a durable press:



Well, in conclusion, remove the press no earlier than a day later and check in a basin of water whether the place that was glued is leaking.

IN Lately Rubber boots are used not only in the country, on hikes or in the forest. Today these are fashionable and stylish shoes that save during heavy rains and floods. The shops are full of bright and colorful boots. However, even such strong and stable shoes can suffer and deteriorate.

Most common problem is a pierced sole. When you step on a shard, broken glass, or even an ordinary pushpin, a hole is formed in the rubber. It is very easy to puncture the rubber material, causing them to leak and become unusable.

But don’t rush to throw away your shoes; in some cases, the shoes can still be repaired. Let's find out how to seal rubber boots at home, how to fix a hole in the sole and in the boot.

How to prepare boots for repair

First, the boots must be thoroughly cleaned, washed and dried. You can seal your shoes with rubber or a patch from an old rubber shoe or tire. To do this, cut out the required piece of rubber and process it on each side with a file or sandpaper. The resulting rough surface will adhere to the glue more firmly and reliably.

Choose a special glue marked “rubber” or “shoe.” By the way, you can find a product for gluing rubber boots in a car store or stores for fishermen and hunters.

Take a glue-sealant that works great. When choosing a product, take into account the shoe material, since EVA and polyurethane require different means. Under no circumstances use classic PVA or “Moment”!

Dried boots need to be sanded and degreased using acetone or solvent. Before using glue, be sure to read the instructions and follow the recommendations.

If the sole, and not the boot, is torn, you must first make the surface smooth and even using sharpening machine. And only then you can glue the patch. Next, we’ll take a closer look at how to seal the sole and boot quickly and effectively.

Five ways to seal your boots

• “Hot” gluing method using a vulcanizer. Rubber is used as a patch, which is pre-soaked in gasoline. The resulting patch is placed on the hole, clamped with a vulcanizer and left for half an hour. Then the device is turned off and cooled. Only after this can the press be removed;
• A standard bicycle repair kit, which includes special patches based on protective films, glue and sandpaper, will help you repair rubber shoes. Required area on boots, sand and degrease. Then remove the film from the bookmark, apply glue and glue it to the desired location. It is advisable to wait 6-12 hours and only then use the shoes. However, the appearance of a glued patch is not very aesthetic, so this method is suitable for repairing soles or for using boots in places where appearance is not important.
• We repair boots using special means for gluing rubber shoes. This is the easiest and available method. First you need to prepare the patch and boots for gluing. Don't forget to degrease the shoe surface. Apply glue to the patch and the gluing area in several layers and apply each layer after the previous one has dried slightly. Press the surfaces to be glued tightly and firmly against each other. To be more effective, you can tap the gluing area with a hammer. To prevent the patch from being noticeable, sand the surface of the sealed area with sandpaper;
• If your boots have a porous surface, you can seal the holes without a patch. In this case, the edges at the cut site are turned out and generously lubricated with glue, and then pressed firmly against each other;
• If you use glue-sealant, which is sold in car dealerships, you can also repair shoes without patching. First, degrease the bonding areas, and then lubricate the torn edges and press them tightly together.

How to properly care for rubber boots

If you choose the right glue and carry out the procedure carefully, you will be satisfied with the repair. And for boots to last longer, you need to organize proper care for rubber shoes and repaired products. After use, thoroughly clean and wash your boots in running water.

We offer several simple rules on the care and use of rubber shoes:

• Wipe rubber surface clean cloth outside. For very dirty shoes, first rinse in water and then wipe dry;
• Colored boots are cleaned with Vaseline. It will retain color and shine, and the boots will not burst or become cracked;
• Be sure to use shoe insoles, preferably warm ones. Wash insoles every two to three months;
• Do not wear rubber boots in hot sunny weather, as the rubber deteriorates and fades;
• Periodically lubricate the surface of the products with oil varnish with rubber glue or glycerin. This will keep the boots shiny;
• Before long-term storage Be sure to lubricate your shoes with glycerin. Then wrap the items in newspaper or paper and place them in a cool, dry place;
• Put away dark spots and stripes from rubber can be done using a regular school eraser. It should be soft and clean;
• If your foot does not fit into the narrow top of the boot, lower the elastic stocking inside and put on the shoes. Then the leg will fit in without any problems, and the stocking can then be easily pulled out.

To keep your shoes shiny and attractive in appearance longer, lubricate the surface with oil varnish and rubber glue or wipe with a damp cloth containing glycerin. By the way, glycerin is an excellent product for caring for leather items. It will help smooth out a genuine leather jacket and give the product a presentable appearance. Learn more about how to care for leather jacket, read.

Rubber boots are footwear necessary not only for the country house, but also for the city. They protect from bad weather and dirt. But it has one drawback - any nail or piece of glass is enough to render the shoes unusable. It’s impossible to give such boots to a workshop, but it’s a shame to throw them away. Therefore, many people prefer to repair their favorite shoes themselves.

How to care for boots

Rubber shoes must be properly cared for. And then you won’t have to resort to frequent repairs. After all, even high quality, which is guaranteed by the manufacturer, does not always mean the safety of the shoes.

Rubber boots need to be cleaned properly. They are best washed with a solution of glycerin and water. In this case, boots should be wiped with a soft cloth and dried often to prevent fungus from appearing. Wet rubber boots cannot be dried with a hair dryer or radiator. It is necessary that the shoes dry naturally.

In order for the repair of boots to be successful, and for the shoes to last for a very long time, you need to know the following:

1. Before repairing, rubber shoes must be very thoroughly cleaned, washed and dried.
2. The patch can be cut from a tire or old rubber boots.
3. It is better to carefully process the patch on the reverse side with sandpaper or a file to make the surface rough for better adhesion of the glue.
4. It is best to degrease the surface of shoes with acetone and solvent.
5. You need to choose a special glue, which must indicate, for example, “shoe” or “rubber.”
6. Before repairing rubber boots, be sure to read the instructions from the glue manufacturer in order to do everything correctly.
7. It is best to smear the patch and the gluing area special glue several times, after waiting until the first layer dries a little.
8. When gluing the surfaces, you need to press them very hard against each other or tap the gluing area with a hammer.
9. A patch on a boot can be easily masked using sandpaper.

Method 1. You can seal your boots with special glue. It can be purchased in stores for hunters and fishermen. But in order to acquire the right glue, you need to know what exactly the shoes are made of. The fact is that shoes made of EVA or polyurethane require different adhesive compounds.

The seller can help you purchase the necessary glue by giving advice. Then everything is simple - you need to sand and degrease part of the boot and stick on a patch. If the shoes are made of porous material, then they can be glued without using a patch. The edges at the cut site just need to be turned out, generously coated with glue and pressed together.

Method 2. For this method you will need a regular bicycle repair kit. It contains patches on special protective films, sandpaper and, of course, glue. Right place on shoes, clean with sandpaper and thoroughly degrease. Next, after first removing the film from the patch, you need to apply glue to it and press the patch to the hole. You can use the shoes almost immediately, but it is better to wait at least 12 hours. The only drawback of this method is the unaesthetic appearance of the shoes after repair.

If the hole appears not on the boot, but on the sole, the gluing technology does not change. You just need to make the surface smooth and even, because usually the sole on such shoes is quite textured. This is possible using a sharpening machine. And only then glue the patch to this place.

But it is important to know that such a patch will not last long, especially if the sole of the boots comes into contact with a rough and hard surface very often. Therefore, it is better to wear such boots, for example, when fishing. Well, if the sole breaks again, the gluing procedure will need to be repeated.

Method 3. In order to seal women's boots without using patches, etc., you need to purchase an adhesive sealant. This can be done at any car enthusiast store. First you need to degrease the gluing area, and then lubricate the torn edges with glue and press them together. If you do everything carefully, the boots will look like new.

Method 4. This method of repairing rubber shoes is also called the “hot” method. It is not complicated, but it requires certain skills and, most importantly, a vulcanizer. Rubber pre-soaked in gasoline is used as a patch. It is placed on the hole in the boot and clamped with a vulcanizer. The device needs to be turned on for 20–30 minutes, then turned off and cooled. Only after it has cooled can you remove the press.

Don't despair if your favorite rubber boots suddenly break. All you need to do is put in a little effort and the repaired boots will be no different from new shoes. You can use taped boots a day after the patch was applied. But if you don’t have time to wait, then you can wear them in an hour.

Video: how to seal rubber boots with your own hands