Help on Tele2, tariffs, questions

Photo wallpapers allow you to quickly and easily diversify the decor of walls and ceilings. They are sold in the form of cut and numbered sheets that must be arranged in a specific order. It is important to properly prepare the wall, since photo wallpaper must be glued to a perfectly flat base. In general, even a novice master can complete the work, since it does not require great experience and special knowledge.

Where to start gluing photo wallpaper?

So, you bought photo wallpaper to create in the room cozy corner. Before choosing, we determined their size and location on the wall. Surface preparation includes the following steps:

• leveling the wall with plaster;
• sealing holes and cracks if alignment is not performed;
• priming the surface with a primer deep penetration.

How to prepare a wall with a finished repair?

It often happens that a wall has already been renovated, but after that a decision is made to change the design. Before gluing photo wallpaper to a wall with a finished repair, the surface must be cleaned to the size of the insert. For work you will need the following tool:

• wallpaper knife;
• long ruler or rule;
• metal spatula 15-20 cm wide.

The sequence of cleaning the wall from wallpaper:

1. Draw the junction lines of the main wallpaper and photo wallpaper with a pencil.
2. Attach a ruler and draw a wallpaper knife along it. Remove unnecessary material. Use a spatula, and areas where the wallpaper cannot be removed can be blotted with a wet sponge or sprayed with a spray bottle.
3. In the cleaned area, repair holes and dents, if necessary. In this case, leveling with a layer of plaster is not done to avoid sharp drop sections of the wall.

Do I need to wash the whitewash?

If the wall is painted or whitewashed, it must also be cleaned, since photo wallpaper cannot be glued to paint. They may come off and the work will have to be redone. The same applies to whitewashing. If the wall is treated with lime or chalk, the whitewash must be washed off with a brush, sponge and warm water. It is better to work in protective clothing, glasses, and rubber gloves.

Making the markings

Photo wallpapers are always accompanied by a diagram of the arrangement of sheets on the wall. It is important to follow it exactly; this will allow you to correctly glue the most complex pattern. Markings are made on the wall to indicate the location of each sheet. It is important to place them strictly vertically and horizontally so that the design is not distorted. To do this, markings are made using a plumb line and building level. Draw better with a simple pencil, and not with a marker, ink or gel pen.

Types of photo wallpaper and choice of glue

Work begins with the first sheet, then take the 2nd, 3rd, etc. according to the manufacturer’s numbering. The brand of glue must match the type of material chosen. For example, if it is paper, choose a glue labeled “For paper wallpaper” or “For all types of wallpaper.”

The construction market offers the following types of photo wallpaper:

• paper (glossy or matte);
• fabric (special glue is included in the kit or you need to buy glue for the textile base);
• vinyl with imitation of various textures: sand, plaster, bark, dust, leather, fresco, frost, painting, weaving, linen.

Rules for gluing photo wallpapers

It is important to properly glue each sheet at the stage of pressing it against the wall. Here it is better to take a pressure roller, since you need to paste the photo wallpaper so that it does not stretch at the edges even by a few millimeters.

Otherwise, this will lead to displacement of the joints and distortion of the pattern. It is better to use a roller with soft rubber; this type of coat is designed for pressing surfaces. The gluing rules are similar to working with standard wallpaper . Only the order changes: work starts from the left top corner

Additionally, the joining seams should be coated. To do this, it is better to take a thin brush so as not to stain the adjacent canvas with glue. Many craftsmen use PVA glue for joints. It should be noted that after drying it gives a yellowish tint, and it is most noticeable on a white background. Any excess glue should be removed with a soft, dry cloth. Same as when gluing regular wallpaper, it is necessary to exclude a draft in the room until the wall is completely dry.

Is it possible to glue photo wallpaper onto other wallpaper?

Let us immediately note that the option of gluing new photo wallpaper onto old wallpaper exists, although this operation requires compliance with the following number of factors:

• The textured ornament of the old coating should not have a thickness of more than 0.2-0.3 mm;
• Photo wallpaper must have simplest option pasting;
• Their density should be from 200 g/m2 or more;
• The old base must have a moisture-repellent coating and not have obvious defects.

The structural drawing requires special attention. Provided that its depth differs from the parameters stated above, you should refuse to paste it - there is a high probability that the pattern will appear through the wallpaper glued on top.

Remember that photo wallpapers with a solid pattern or halftones are unlikely to be able to completely hide the pattern underneath. Preference should be given to options with non-contrast small prints. Canvases with forests, thick grass, lots of lights, a busy metropolis or an orchard look great.

If there is a need to glue photo wallpaper onto non-woven wallpaper, you should take into account their density - it should correspond as closely as possible to paper. The quality of the glue is also of great importance - it is not right choice can ruin all your efforts.

If there is a discrepancy between the parameters of the old and new wallpaper, it is better not to stick it. In this situation, you need to be patient and first get rid of the old coating.

Who doesn’t dream of living on the seashore or near a forest to enjoy the beautiful scenery from their window? Or in the evenings admire the flames in the fireplace in your living room? There is a wonderful way to turn such fantasies into reality quickly and without capital expenditure - covering the walls with photo wallpaper.

Photo wallpaper – Sea view

Photo wallpapers and their history

Since ancient times, people have had a desire to decorate their homes. Cave paintings have been found in ancient caves! Since then, this desire has not waned. The room was decorated with frescoes, mosaics, artistic painting, tapestries, carpets.

Decorating walls with paper with a pattern printed on it was invented in China a thousand years ago. After the invention of rice paper, it began to be used for pasting rooms. Previously, beautiful landscapes and original scenes were depicted on the sheets. This was the prototype of modern photo wallpaper.

Over time, decorating homes with pictures began to be used in Europe. In the Middle Ages, paper was no longer an expensive material, and there were plenty of court artists. The technology for making wallpaper with pictures has also changed: they switched to using wooden forms, templates, special machines that made it possible to print several dozen linear meters wallpaper per day. Therefore, such decoration of the room was no longer a luxury item and became widespread.

Pasting photo wallpapers again rose to the peak of popularity in the 50s of the twentieth century. During this period, color printing was already invented and methods of applying a printed image to different types of paper were improved. These were already real photo wallpapers that we were used to seeing in photos of our parents or in movies of that time.

Since then, the fashion for photo wallpapers has faded away and then reappeared. Their great popularity was noted in the 80s. Next period The heyday of this trend in interior design has already occurred in our time. This was facilitated by the emergence of digital printing equipment, eco-friendly paints for applying images, high-quality vinyl-based paper.

Today, the use of photo wallpaper is one of the most fashionable trends in the field of room design. Photo wallpapers from the komar company are very famous, creating the most realistic sensations. They have high quality, are absolutely harmless to the human body and are quite affordable even for a buyer with average income.

Types of photo wallpaper

There are several types of photo wallpaper. This classification helps you figure out which photo wallpaper is better in quality. Each type has its own advantages and purpose.

1. Paper photo wallpaper. They are produced on thin paper using offset printing. This is the most economical option. They have good moisture and breathability. Overlapping gluing is allowed. Suitable for bedroom, office. However, the image and color rendition are noticeably worse than other types. There are inconsistencies between in separate parts Pictures. Problems often arise when gluing, since the wallpaper quickly gets wet, and there is no possibility for adjustments. In addition, they fade quickly and absorb odors. They are easily subject to mechanical stress, so they are not recommended for corridors and kitchens. Suitable for short term use only.
2. Texture photo wallpaper. This is wallpaper that is printed on non-woven or vinyl based. They are dense, soft, have a pleasant texture, and do not contain harmful substances. Can be performed in various options: (plaster, sand, canvas, linen, frost, painting, Venetian plaster). They have high quality images. Easy to stick. Durable, do not scratch, wash well. It is better to choose such photo wallpaper for the living room. Disadvantages include their airtightness and problems with joints if glued improperly.
3. Glossy photo wallpaper. Their distinctive feature is a smooth glossy surface that is created using lamination or varnish coating. This serves as good protection against burnout and mechanical stress. More rigid to the touch. May have different bases. They wash well. Very practical, suitable for the hallway, nursery and kitchen. They have poor breathability. Required for gluing careful preparation walls During operation, fingerprints may remain.
4. Self-adhesive photo wallpaper. They have a ready-made adhesive layer that is covered protective film. Easy to stick, adjustments can be made within a few hours. They have excellent performance data. Intended for smooth surfaces, not suitable for plastered walls.

Glue selection

The proposed classification helps to better understand what glue to use to glue photo wallpaper to the wall. First of all, you need to pay attention to the instructions included with the product. Responsible manufacturers indicate the recommended type of adhesive. Sometimes glue is sold together with wallpaper, but more often you have to buy it separately.

Under no circumstances should you buy universal glue!

The main thing to consider is the substrate on which the image is printed. Paper photo wallpapers are called lightweight, and for them it is recommended to purchase glue intended for ordinary products. All others are classified as severe types. In this case, you need to look for glue for vinyl wallpaper.

The best option is glue containing PVA and starch. You should also pay attention to the absence of a pungent odor, the presence of moisture resistance, and an antifungal effect.

How to glue

Pasting photo wallpaper with your own hands is a very troublesome task that requires skill and patience. For such work it is necessary to prepare:

• glue and container for diluting it;
• brushes for applying glue (wide and small);
• rubberized roller or plastic spatula for smoothing on the wall;
• sponge for washing off glue from wallpaper;
• bucket with water;
• rags for wiping hands;
• plumb line or level;
• pencil;
• roulette;
• ladder.

Before sticking photo wallpaper on the wall, all parts of the picture must be laid out in in the right order, cut off the white marking stripes. Below you can see the order of work.

Preparing the walls

Before starting work, it is important to pay attention to which wall to glue the photo wallpaper on. This must be Smooth surface, cleared of old wallpaper. You shouldn’t skip this stage and “be smart” by thinking about how to stick photo wallpaper on a wall with wallpaper. Their color and texture may appear on the surface of the photo wallpaper.

Therefore, the old layer must be removed using a metal spatula. It is imperative to remove switches, sockets, and baseboards. Then the wall must be plastered, primed and waited until it dries.

If the wall is smooth, you can simply wash it to remove dust and dirt. Sometimes the surface is painted in light colors.

You need to achieve a perfectly smooth plane, because even small grains will appear against the background of pasted photo wallpaper.

Thinking about whether it is possible to glue photo wallpaper on vinyl wallpapers, it is important to remember that in this case, in addition to the visual defect, it will be very difficult to achieve strong adhesion.

On final stage preparatory work markings are applied. This is done using a level or plumb line. First, a vertical line is drawn along the edge and a horizontal line along the top of the wall. When deciding how to properly glue 8-piece photo wallpaper, you can apply marks for each square.

Applying glue

Photo wallpaper is a rather “capricious” material that can wrinkle, stretch and even tear. This especially needs to be taken into account before gluing photo wallpaper on paper based.

It is important to pay attention to the consistency of the glue; it should be without lumps. There is a rule: the thicker the base of the photo wallpaper, the thicker the glue should be. Very liquid glue is not suitable, because when using it, the sheets get wet very quickly.

There are two ways to apply glue. Paper photo wallpapers are glued immediately after lubrication. But other types of photo wallpaper, after applying the glue, need to be folded and left to soak.

Adhesive for photo wallpaper is applied both to the sheets and to the wall. Sometimes, if indicated in the instructions, only the wallpaper is lubricated and applied to a dry surface. You only need a small amount of glue!

When smoothing the canvas, the remaining glue is squeezed out and then washed off with a wet sponge. You need to start leveling from the center and only with a roller or plastic spatula.

Do not wipe with a rag, as this can ruin the appearance and texture of the photo wallpaper.

Gaps

When gluing photo wallpaper, the most difficult task is to correctly connect the individual parts so that all the details of the picture completely coincide. There are two options for this process. Some types, for example, mosquito wallpaper on a non-woven basis, are glued end-to-end . It is easier to work with them, since the main thing is to avoid distortions in their placement on the wall.
Most photo wallpapers are glued with an overlap. In this case, after achieving perfect alignment of the pattern, you need to cut off the excess parts of the sheets. To do this you need to use a knife and a ruler.

It is important that the cut is to the depth of both strips and runs exactly along the alignment line.

Then the sheet of joints should be coated with glue again with a small brush and rolled tightly with a roller to the wall. Such actions must be performed sequentially, with each sheet separately. Finally, you need to once again “roll” all the joints with a roller and thoroughly rinse off any remaining glue.

Photo wallpapers are one of the main ways to decorate a room, visually change its parameters, add comfort and originality, and reflect the individuality of the owner of the house. With the right choice and skillful gluing of them on the wall, they can become a real highlight. interior design and delight you and your guests.

Today we’ll look at how to glue photo wallpaper on the wall in detail. Everything is done with your own hands, so the price will not be significant. Although here you will have to observe principles and follow some rules. How to properly glue photo wallpaper on a wall will be discussed below.

Now let’s look at how to hang photo wallpaper on a wall point by point. This is a responsible and creative process. After all, it is quite possible to change the visual perception of the room. It needs to be comfortable and attractive. First, you should look at the photos and videos and choose the right option. Let's look at the whole process in more detail.

Choosing the best glue for different types of wallpaper

It is no secret that a stingy person will pay twice. This expression is also relevant when selecting glue for gluing wallpaper such as vinyl. You have no right to make a mistake when wallpapering. And you won’t be able to re-glue the canvas again.

• Before you decide to buy glue, you need to decide what type of wallpaper your wallpaper belongs to. All wallpapers can be divided in connection with this classification into such types as universal, as well as special. As for universal glue, it is suitable for any type of wallpaper, which is why it is named, and special glue exists for those wallpapers that have a vinyl coating.
• On the wallpaper packaging you may find an inscription such as “For light wallpaper” or vice versa, this is very important for choosing adhesive.
• As for light wallpaper, this includes all paper-backed wallpaper, and heavy wallpaper includes acrylic, vinyl (see), etc.
• There are also cases when the wallpaper manufacturer indicates that the wallpaper is of medium weight. This type may include wallpapers such as acrylic and textile.
• When choosing wallpaper glue, pay attention to the weight of the wallpaper, as well as the material from which the wallpaper is made. An important factor when choosing wallpaper and glue for it is humidity, as well as room temperature. Pay attention to what critical indicators the glue you choose has.

Note! When buying cheap glue, money will be thrown away. What to do right choice, you just need to carefully read the instructions on the packaging. To make the right choice when buying glue, trust proven and popular companies. But you should not think that if the glue is the most expensive, then it will necessarily be of high quality. So, when buying glue, you should use the “golden” mean.

If vinyl wallpaper contains non-woven material, then you should choose non-woven adhesive. It is because of its composition that the glue received its name.

Choosing glue for heavy wallpaper

There is no definite and clear advice on this matter.

The choice of glue for heavy wallpaper is quite simple:

• For this type of wallpaper, you should choose an adhesive whose packaging indicates that the adhesive is intended for heavy wallpaper. But you should not choose glue labeled “universal” for such wallpaper.

Tsugunov Anton Valerievich

Reading time: 5 minutes

Modern finishing materials amaze with their abundance decorative properties. This is especially true for photo wallpapers that seem to transport you to distant lands, fairy meadows, other planets, and endless ocean spaces. Such a presence effect is only possible if such wallpaper is glued correctly, otherwise uneven joints, distortions, air bubbles, and folds will ruin the whole impression. We suggest you figure out how to glue photo wallpaper without mistakes.

Pasting photo wallpaper on a wall with your own hands is a simple procedure, but it requires extreme care and attention.

Features and nuances of gluing different types of photo wallpapers

Based on the material used, wallpaper can be divided into several types, and the process of gluing each of them to the wall has its own nuances.

Paper

Paper photo wallpapers can be one- or two-layer. Due to their increased strength, the latter are quite easy to work with, but single-layer paper canvases are very capricious during the process of unfolding and gluing, they tear easily and form folds. We work with them very carefully.

Soaking time adhesive mass paper wallpaper with a photograph – 3–7 minutes. If you overdo it, there is a risk that the canvas will get wet. The thinnest single-layer wallpaper must be attached to the surface immediately after coating it with glue, otherwise it will tear.

After drying, all defects in the surface of the base will be visible through such photo wallpaper, so it must be prepared as carefully as possible. But paper webs are undemanding when it comes to glue.

Vinyl medium density photo wallpaper

Such canvases have a smooth or foamed coating and are resistant to moisture and abrasion.

The composition of the glue and the method of applying it to the wall are selected based on the base of the photo wallpaper - non-woven or paper.

• When choosing a paper-based material, glue is applied to the wall and to the canvas 5–10 minutes before gluing.
• When working with non-woven wallpaper, the adhesive composition is applied only to the wall. For better adhesion, you can coat the edges of the canvas from the wrong side.

Non-woven photo wallpaper

One of the most common options with an attractive appearance and affordable cost. The reverse side of such products is similar to paper, the front covering is easy to clean, so they are suitable for kitchens. Abrasion resistant and mechanical damage, in their texture most often imitate plaster.

When gluing non-woven wallpaper, the adhesive composition is applied not to the canvas, but directly to the base.

Non-woven wallpaper glued to the wall has the property of holding the surface together; when shrinking a new house, they will prevent cracking of the plaster.

Fabric photo wallpaper

The densest type of material made from natural textile fibers (linen, silk, cotton). Gluing requires a certain skill, so as not to spoil an expensive product, it is better to seek help from specialists.

Canvas with 3D effect

Let us separately highlight 3D photo wallpapers, which help to visually expand the space and create the effect of presence. This coating is especially appropriate in small spaces. They are usually glued over the entire surface of the wall, which allows you to achieve the desired result. To create such wallpapers, a non-woven base is used, so they are easy to care for and durable.

Before gluing, the surface must be carefully prepared: leveled and treated with a primer. The connections of the strips should be made extremely carefully so as not to disrupt the integrity of the pattern.

What do you need to hang photo wallpaper?

Tools and materials for gluing photo canvas:

• The wallpaper itself. Before ordering them, carefully measure the wall, decide on the location, size, and theme of the drawing. A rash choice can lead to additional costs for purchasing new material.
• Adhesive composition. Selected based on the type of wallpaper purchased. Before purchasing, check with a sales consultant in a specialized store to make the right choice. Pay attention to its color so that the glued pattern is not spoiled by visible stains of the adhesive composition.
• Stationery knife. It will help to smooth out uneven surfaces and trim protruding ends of the wallpaper.
• Several brushes. Use small brushes to glue the joints, large brushes to apply the composition to the main part of the canvas.
• A simple pencil. Necessary for marking on wallpaper and on the wall.
• Level. Helps identify correct proportions vertical and horizontal lines.
• Ruler. Used to draw boundaries between parts of a drawing.
• Pure matter. It will come in handy if the adhesive composition goes beyond the edges of the pasted photo wallpaper.
• Rubber roller. With it in your hands, you need to walk over the pasted wallpaper, correctly distributing it over the surface of the wall, expelling air bubbles.

The process of gluing wallpaper with a photo image

The rules for gluing photo wallpaper are usually indicated on the packaging. However, in case the instructions offered by the manufacturer are not clear, we offer a step-by-step lesson:

• We decide on the wall where the wallpaper will be attached.

Note! Non-woven and vinyl canvases will hide minor imperfections in the base surface.

• We carefully prepare the selected wall, clean it of the previous finish, remove all cracks, chips and large irregularities. To make the design more bright, paint the base with white water-based paint.

Important! The room temperature before, after and during wall pasting should be maintained at 25 °C.

• We carefully inspect the purchased photo wallpaper to make sure that all parts of the picture match and correspond to the stated dimensions.
• We mark the wall in advance, marking on it the future location of each of the fragments.

It is customary to start marking from the part of the image that will be closest to the window.

• We apply adhesive to the back of each fragment. Leave the strips for some time to soak (on average 10 minutes is enough). If non-woven wallpaper or vinyl wallpaper on a non-woven basis is glued, the glue is applied to the surface of the wall.
• According to the markings made in advance, we paste the canvas fragments.
• Smooth out the applied pattern using a rubber roller.

• When gluing with an overlap, carefully remove the excess parts.
• We cut out “windows” for sockets.
• When specified in the instructions, we apply a protective composition.

If some aspects of the above process are still unclear, watch the following video tutorial:

The master in the video reveals several professional tricks that will definitely come in handy when covering walls with photo wallpaper yourself. If there are still concerns that with my own hands If you won’t be able to complete the job flawlessly, we recommend checking with professionals how much it costs to hang wallpaper with a photograph. Most likely, the announced amount will not be that great, especially in comparison with the opportunity to get a magnificent interior.

(votes: 2 , average rating: 5,00 out of 5)

Today, in the interior design of an apartment or country house Photo wallpapers are often used. This finishing material allows you to decorate walls and visually expand the space, therefore it is especially popular among owners of living space in apartment buildings. Before you hang photo wallpaper on the walls, you need to find out which products are best to choose and how exactly to apply them.

Photo wallpapers are classified depending on many features, but there are 3 main factors.

Density

According to this indicator, the material is:

1. 90–120 gsm m. Usually this is paper wallpaper, similar to products Soviet period. The base is very thin, so when unfolding, transporting and pasting the products require careful attitude. The service life is quite short, but the cost is the lowest. You can hang such wallpaper yourself using PVA glue.
2. 150–250 gsm m. Most often, the base is made of vinyl. The thickness of the material allows it to be embossed, which is why there are models with relief patterns. Pasting can also be done independently, but using special glue.
3. 300–400 g/sq. m. These wallpapers are considered the best in terms of price and quality ratio. Can last 10–15 years, provided correct application and operation.
4. More than 400 g/sq.m. m. The densest and most durable products, and at the same time the most expensive.

Photo wallpaper with a density of 300–400 g/sq. m are considered the most the best option, they are resistant to light mechanical damage and are able to hide minor wall defects

Material

Depending on the materials used in production, wallpaper has certain performance characteristics.

Paper

The simplest and accessible view. Today they are used extremely rarely due to their low strength. They are suitable only when you need to quickly and inexpensively update a room for a short period. In other situations, it is better to purchase photo wallpaper made from modern materials.

The only advantages that can be noted are low cost, availability and the absence of the need to use special adhesive compositions. There are many more disadvantages:

• Low moisture resistance.
• Exposure to sunlight.
• After the glue dries, defects will appear on the surface.

In addition, there is difficulty in gluing: if you do not saturate the wallpaper with glue enough, then it will not stick to the surface. If you apply a lot of composition, the paper will get wet and the wallpaper will crawl.

Non-woven

One of the most popular types of photo wallpapers today, they look like paper ones. The fact is that non-woven fabric - non-woven material, consisting of cellulose, so it has some similarities to paper. Advantages:

• Saving glue. The composition should only be applied to the wall.
• Easy to paste.
• Reusable.
• Plastic. The wallpaper will not tear due to shrinkage of the building.
• Allows you to disguise minor defects.

Textile

Analogues of this material have been known to mankind for several centuries. Such wallpapers belong to the elite category, so their price is appropriate. Made from natural materials: linen, silk, cotton and so on. The base can be paper, PVC or non-woven fabric; there are self-adhesive models. The main advantage is long term operation. Disadvantages include high cost and inconsistency with some modern styles interior

The textile version has good sound and heat insulation, this type photo wallpapers are often produced seamless

Vinyl

Wallpaper, which is made on the basis of one of the types of plastic, so it is resistant to moisture and very durable. But such material requires a perfectly prepared surface, otherwise folds will appear.

3D wallpaper

These products are placed in a separate group because they cope better than others with the task of visually expanding space. They are usually placed along the entire wall from ceiling to floor. Non-woven fabric is used to make such products. The advantage is the wide range, the disadvantage is the complexity of gluing.

Figure location

Pasting photo wallpaper with your own hands begins with determining the location of the image:

1. Zonal. In this case, wallpaper is glued to one section of the wall. This position is used to create emphasis and visual increase
2. ceiling height.
3. Modular.
4. The product occupies part of the surface, and the image is made up of two, three or more fragments.

Angular.

Wallpaper is glued to part of the area of ​​adjacent walls.

Panoramic.

Wallpaper takes up the entire surface area. They may consist of a single piece of fabric or several strips. Types of photo wallpapers by pattern location: 1 – zonal, 2 – modular, 3 – corner, 4 – panoramic Is pasting over old wallpaper acceptable? The most difficult and time-consuming stage is the preparatory stage, when you need to remove the previous coating. In this case, the question arises: is it possible to glue photo wallpaper to old products? This is possible if the material fits tightly to the wall and has retained its original integrity. Also, before gluing to old wallpaper, you need to check whether mold has formed on the surface. Important! You can glue new photo wallpapers onto old ones only on the condition that

existing coverage

no relief patterns. Otherwise

new material

won't stay on the wall.

• Technology of covering walls with photo wallpapers
• Gluing photo wallpaper to walls is quite simple; it is more difficult to prepare and mark the surface.
• Tools
• The following tools are required:
• tape measure, ruler, marker;
• building level;
• container for preparing glue;
• ladder.

stationery knife;

Regardless of the thickness and density of the purchased wallpaper, the surface must be carefully prepared, otherwise defects will appear after the solution has dried.

1. Using a building level, it is necessary to determine the collapse of the wall. If the curvature of the surface is slight, you can process it finishing putty. If there is significant blockage, leveling with plaster or drywall will be required.
2. Next you need to examine the walls, find all the potholes, cracks and other defects. Metal elements, protruding from the surface are trimmed with a grinder, and screws or nails are removed. Large potholes are being filled up cement-sand mortar, which dries long enough.
   

   Attention! Until the mixture has completely dried, you cannot proceed with further finishing works. It is also prohibited to speed up the process using heating devices.

3. After plastering, it is necessary to treat the walls with finishing putty, and when it hardens, apply two layers of deep penetration primer with an interval of 4 hours. This is necessary to increase adhesion and better contact of the wallpaper with the surface.

Stages of preparation of the base: 1 - determining the blockage of the wall, 2 - sealing holes, 3 - finishing puttying of the walls, 4 - priming the surface

Making glue

This process must be carried out in strict accordance with the manufacturer's instructions. Typically, to prepare, pour the dry composition into a clean container, add half the required amount of water and mix thoroughly. Then gradually introduce the remaining amount of water, mix again and let the glue sit (time specified by the manufacturer). After this, mix again, the composition is ready for use.

Marking

While the glue is infusing, you can start marking, which will determine the exact location of the image. The first step is to apply wallpaper and mark its boundaries. Then use a level to draw horizontal and vertical lines. Depending on the material, the area is divided into squares or rectangles of appropriate sizes.

The process of gluing canvases

Now let’s talk about how to properly hang wallpaper on the walls. General technology is as follows:

1. Apply glue to a section of the wall. If you use paper wallpaper, you need to coat it too. You should not apply glue to all strips of material at once so that they do not get wet.
2. Fold the strip three times and leave it for 3-10 minutes to soak. In this case, it is very important to act carefully so that erased lines do not appear at the fold points.
3. Glue the top piece. It is applied to the marked wall and aligned along the lines.
4. Use a rubber spatula to remove air from under the wallpaper from the center to the edges.
5. Glue on the same side bottom part. The application technology is the same, but it is important to combine the pattern.
6. All the fragments are glued one by one so that a clear image is obtained.

VIDEO: how to properly glue photo wallpaper to the wall

Some wallpaper models are joined end-to-end, and some are overlapped, so it is recommended to first lay them out on the floor to determine the joint. It is easier to design the borders of pasted wallpaper if they need to be adjacent to each other. To do this, the canvas is simply adjusted to the previous one.

For overlapping pasting, it is necessary to combine the fragments so that the correct pattern is formed. Using a marker and a ruler, you need to draw a line at the junction and draw along it with a stationery knife, cutting off the excess part. The resulting joint should be coated with a brush. Finally, it is recommended to roll all the seams with a rubber roller and remove any remaining glue.

Photo wallpaper is one of the most interesting and effective ways decorate your living space, give it comfort and originality. Provided that the pasting technology is followed, photo wallpaper will last a long time and will become a real decoration of the home.