Help on Tele2, tariffs, questions

Instructions for making palm trees from plastic bottles.

Nowadays there are many ways to decorate your country cottage area. For this purpose, plastic bottles, tires and flower pots. If you wish and have a good imagination, you can come up with your own new option creating an exotic tree.

Basic materials for making palm trees for the dacha:

• Plastic bottles
• Flower pots

Below are interesting and non-standard options for making palm trees for a summer cottage.

It all depends on the size of the tree. If you have a summer cottage big size, then you can make a fairly tall palm tree with a lush crown. It is enough to take 10-15 plastic bottles for the trunk Brown. The approximate volume of bottles is 2.5 liters. The larger the bottle, the larger the barrel diameter will be. For a crown you will need 10-30 plastic containers Green colour. This variation in quantity is explained by the fact that the shape of the leaves can differ significantly.

How to make a palm tree with your own hands from plastic bottles step by step: step-by-step instructions

There are many ways to make an exotic tree. The methods for cutting bottles differ. It depends on the availability of free time and imagination.

Materials for making palm trees:

• 12 2.5 liter bottles brown
• 20 green bottles of 1.5-2 l
• Cable, thickness 1-1.5 cm
• Metal pipe for stem

Instructions:

1. Take brown containers and cut the bottom along the contour of the recesses, as a result the bottom of the bottle should resemble an asterisk
2. Cut the container 10 cm before the neck of the bottle, you should get 6 petals
3. String the prepared bottle structures onto a steel tube previously dug into the ground. You should get a relief trunk
4. Start making leaves. It is necessary to cut green containers in half and cut into strips top part. The width of the strip should be 2-3 mm. The thinner the stripes, the fluffier the crown
5. Now string 4 plastic pieces onto the cable. The cable must be sufficiently rigid. It should bend well, but also keep its shape
6. Attach a sheet of wood with 5 holes in a circle to the top of the rod with the trunk. Insert the prepared leaves into these holes. Adjust bottles if necessary

The barrel can be made by cutting a pipe from a plastic bottle. But there is also an option that will allow you to use the bottoms. In this case, much more raw materials will be needed.

Instructions:

• As a basis for making the trunk, you can use a flat wooden log of the required height
• Cut off the bottom of a brown plastic bottle. Using screws, screw the bottoms into the barrel
• Do this in a circle, imitating the topography of a palm tree trunk
• Continue screwing the bottoms until the very top of the log
• But you can make a palm tree trunk from the cylindrical part of a bottle
• To do this, the lower part is cut off, and the bottle itself is cut only halfway into 6 petals
• After this, the bottles are connected to each other

The crown can be made using green plastic bottles. The density of palm branches depends on the number of plastic bottles.

Instructions:

• To do this, you need to take green bottles and cut them into thin strips, after cutting off the bottom
• In this way, a branch is formed of several bottles, which are then fastened together by stringing one on top of the other
• If there are not so many bottles, then you can make the branches differently. To do this, the green container is cut into 5 parts, not to the end of the bottle. There remains a distance in the neck area
• Using scissors, a kind of fringe is made along the edges of the cut petals. It is necessary to make it stick out in different directions
• The resulting leaves must be connected to each other to form a crown.

How to make a crown for a palm tree from plastic bottles?

To do this, you need a base and the leaf blanks themselves.

Instructions:

• Take copper cable cut it into small pieces
• String the workpieces onto the wire and secure the edges
• Bend the cable if necessary
• Next, you need to insert the leaves into the base for the crown, this can be a metal ring or a piece of wood with holes

How to make a palm tree from plastic bottles

The palm tree is collected from the bottom up. To do this you will need the following components:

• Barrel blanks
• Metal pipe
• Crown
• Scotch

Instructions:

• Starting from the bottom, assemble the stem by stringing bottles one after another. You can fasten them using tape or a hole punch.
• Assemble the crown by staggering the leaves. Straighten the branches and bend them using the cable.
• You can add texture and fluffiness to the leaves using scissors. Heat is also used to curl the petals. This can be done using gas burner or a regular fire.
• It is necessary to connect using tape; when there is 30 cm left to the top, it is time to assemble the crown.
• Attach the crown to the trunk. You can fix the top of the palm tree with its trunk using construction stapler, liquid nails or tape.

Making a palm tree from plastic bottles is not at all difficult. All you have to do is be patient and use your imagination.

VIDEO: Bottle palm tree

Simple and in an inexpensive way You can renovate the area near your home or on the playground by making crafts from ordinary plastic bottles. It will take a little time and imagination, and you will be able to create from this universal material whatever your imagination allows. You can, for example, make a banana tree. And so that you can understand how to do this, we created a master class on a palm tree from plastic bottles that are unnecessary on the farm, quickly and easily with your own hands, it contains detailed step by step instructions and photo and video lessons.

Such a tree will serve wonderful decoration holiday for children or theme party. The more plastic bottles you use to create one palm tree, the taller and more magnificent it will be.

Making a palm tree from plastic bottles with your own hands step by step

To create a palm tree we will need the following materials:

1. Plastic bottles different sizes and flowers
2. Scissors
3. Scotch
4. The basis for the future palm tree. Usually a metal rod is used.
5. Frame for future palm tree thick wire or metal pipe.
6. Styrofoam or artificial bananas
7. Yellow paint
8. Wire

1) In order to make a palm tree trunk, you need to take 1.5 liter brown bottles 2 and 2.5. First you need to cut the bottle from the neck side by about a third. You will need the upper part, but don’t rush to throw away the lower part - you can also make a barrel out of it by analogy.

2) Cut the bottom of each bottle with a heated knife. We will attach the frame of our palm tree to this cut.

It is necessary to cut the part of the bottle with the neck into 8 equal parts. You need to cut from the wide edge to the narrow.

Now we need to make these parts pointed in shape so that it looks like a petal.

3) We bend the resulting petals to the outer side - it will look like a blooming flower.

1) So that our banana tree leaves have appeared, you need to take bottles of green (preferably different shades), white and yellow. How more colors you use, the brighter the palm tree will look.

2) Cut off the edge of the neck and the base of the bottle. We cut the resulting blank from the bottom of the bottle towards the narrow part into 3 approximately equal parts, but not all the way. There should be about 3 cm left to the end of the bottle. We give the edges of each part a shape like a narrowed semicircular petal. We begin to carefully bend these petals outward just as we did the trunk of a palm tree. The result will be something vaguely reminiscent of a three-bladed fan. Now we cut each resulting sheet from the edge to the middle. You need to leave a little uncut space in the middle - about 2 cm. It looks like a fringe. The narrower the width of the strips you make, the more magnificent the fringe will turn out, and therefore the foliage of our palm tree.

3) Now the fringe strips need to be bent in different directions. 1- bend it up, 2- leave it as is, 3- down. This is how the sheet becomes voluminous.

4) There are 2 ways to decorate leaves. In the first case, we leave our blanks as is, and in the second, the blanks need to be strung on a flexible wire to create long, voluminous branches. In the second case, you will need more bottles, but the palm tree will also acquire a luxurious crown.

We take a dark brown bottle and cut it like a blank into leaves - from top to bottom into thin strips. We collect the pieces and wrap them inside.

We cut out blanks for bananas from foam plastic and paint them with yellow paint and carefully pass a thin wire through the top.

1) Take a palm tree frame prepared in advance. This could be a thick wire or a metal pipe. And we begin to put the finished barrel blanks on the frame with the neck down. We put on the blanks first bigger size and we begin to compose the details like a designer. We compose until there is approximately 30 cm left to the edge. Try to arrange the petals of each part in a checkerboard pattern. We secure the parts at the base with glue or tape.

2) Depending on what kind of leaves you chose to make, there are 2 methods of attachment: 1-We begin to attach palm branches to the remaining empty upper part of the trunk. This is done in the same way as the trunk was assembled. Don't forget to use details different colors and arrange the leaves in a checkerboard pattern. 2 – attach the cable with the leaves strung on it to the frame of the palm tree at the very top and secure each leaf with tape.

3) Install the crown - glue the workpiece to the edge of the frame with the neck down.

4) We tie artificial bananas to palm branches

To secure our palm tree, we stick a metal pin into the ground about 30 cm deeper for stability (if desired, you can fill it with concrete), but so that at least 40 cm stick out from the ground - to string the trunk and put our palm tree on top.

Now our palm tree made of plastic bottles is ready.

Video on the topic of the article

For clarity, we also suggest you look detailed videos lessons on how to create your own banana tree.

Today, owners of dachas and personal plots are trying in every possible way to decorate the exterior. There can be many ways, starting with landscaping and ending with some buildings. One of the most budget options can be called from plastic bottles. In this article we will tell you how to make a palm tree for your garden plot from plastic bottles.

Materials for bottle palm trees:

• green and brown plastic bottles;
• scissors;
• Metal sheet;
• metal rods;
• metal bushings and tubes;
• high voltage cable.

1. Prepare bottles in advance and remove labels from them. Start by making palm leaves from green bottles. To do this you need to cut the bottle in half.

2. Cut strips on the top of the bottle lengthwise, but not all the way.

4. For one palm tree you will need 7 palm leaves, the length of which you can adjust yourself.
5. To make the trunk, take brown bottles and cut wide strips on them. You should get 6 wide stripes along the entire 2.5 liter bottle.
6. Also string blanks for the barrel onto a high-voltage metal cable.
7. Start preparing the base for the palm tree.

8. Weld two metal rods (at least 25 cm long) onto a sheet of metal. The rods need to be welded under different angles.
9. Take tubes with a diameter of 2 cm and put them on the rods. Weld metal bushings onto the end of the rod so that palm leaves can be threaded through them.

11. Start assembling the barrel from the bottom up.

12. After the entire structure of the palm tree has been assembled, bury it in the ground to a depth of 0.5 m.

DIY palm tree made from plastic bottles ready, now you can create a whole paradise on your personal plot. Don’t be afraid to get creative, palm trees can be any size, and instead of coconuts, attach bright plastic bottles of juice or sweet water.

You can come up with your own scheme palm trees made from plastic bottles.
The first plastic bottle was developed in 1941, and today it is used not only for household purposes and for storing water, but also as a convenient and inexpensive material For .

A person’s desire to decorate his home is not limited to the area of ​​an apartment or house. Going out into the street, it is embodied in flower beds and front gardens, in garden bushes and trees. But seasonal changes in nature they constantly make adjustments to the beauty we have created.

But how can you create such a picture from available materials that can please the eye for many years? We will tell you in this article.

Artificial Palm Tree Material

The raw materials for making a man-made palm tree will be plastic bottles. This is one of the most common containers for various drinks on the planet.

To create a palm tree you will need a large number of same type of plastic bottles in two colors:

• brown: from kvass or beer - for a tree trunk,
• green: from sprite, tarragon or the same beer - for its leaves.

There may be several forms, in which case you will have to alternate them when assembling, but it is better to have the same ones, matching both in color and shape.

Procuring the material will be the most difficult work in the process of “growing” palm trees from plastic bottles with your own hands. But, if you have children and they have friends, then all the work can turn into an exciting cultural and educational event with a small palm grove in the end.

Or not end with only palm trees.

Before use, the bottles should be washed so that the remnants of the drinks in them do not become an adhesive base for dust, and the labels and remnants of the glue with which they were glued should be removed.

Assembling a palm tree from plastic bottles - step by step for beginners

There are a lot of options for making a plastic palm tree, let’s look at the most common ones.

1. Barrel.

It can be based on:

• metal rod or fittings;
• wooden post;
• dried tree.

Let's consider options for making a palm tree trunk. Various technologies were used to make the trunks of these palm trees.

IN first case the tops of the bottles were simply cut off, and they were strung on a rod, inserted into each other. This only vaguely resembles a palm tree trunk, but is simple to do and does not require as many bottles as other methods.

Second option resembles the first one, but in it the tops of the bottles are cut out with a crown, the teeth of which are slightly turned outward.

Third– requires a fairly large number of bottles, but in this way you can decorate very thick bases, imitating real views palm trees with thick trunks, or transform the trunks of dried trees, freed from excess branches, into them.

Sometimes, in order not to look for such a huge number of brown bottles of the same type, they collect white bottles of the same shape, and after screwing their bottoms with self-tapping screws to wooden base trunk, painted with it in the same brown color.

This can be done in a way that is resistant to fading. acrylic paints or automotive enamels, although some use cheaper nitro paints from aerosol cans. Sometimes, with a brush, after the first layer has dried, the recesses are painted in a more dark color, it turns out more realistic. It is better to cover everything with colorless frost-resistant varnish after painting.

To form the texture of the trunk fourth way a fairly large number of bottles are also used, but this imitation looks even more believable and beautiful. Such scales are obtained using the curvature of bottle legs.

Unlike the previous options, formed from below, the assembly of such a “bark” is carried out from the upper part of the “trunk”, when the fasteners of the upper layers (screws, nails, staples) are covered with the lower ones, and the very bottom is dug into the ground or sprinkled with it.

This method is similar to fifth option, only it imitates the appearance of palm trees, the bark of which is formed by leaves that die off as the tree grows, leaving behind protruding thick parts of the cuttings. We will not describe the method of its formation; it is clear from the photograph.

And we will illustrate with step-by-step photographs the simplest of the textured methods, only unlike the photographs in which it is shown, and where only the lower halves of the bottles are used, we will use all the material. We took a white bottle so that the markings would be more visible.

To enlarge the picture, click on it.

The upper part of the bottle, after cutting and bending the ends, is unfolded and inserted into the lower one. Both fit onto a metal rod that forms the shaft and bends to your liking. To do this, holes of the required diameter are drilled in the bottoms of the bottles, as in the photo.

It is not that big: for a 3-meter barrel you will need 19 - 20 two-liter bottles.

To make the plastic more massive and resist creasing in the future, the insides of the bottles can be filled with sand during assembly.

2. Leaves.

Some of them only vaguely resemble palm trees, but they are easy to make.

It’s more difficult when you have to do extra work with scissors.

To enlarge the picture, click on it.

You can lightly cast a spell over the edges of the leaves with an open fire, like on last photo this selection, and they will take on a more natural look, because in nature there are no leaves with rectangular ends.

A reliable fastening will be achieved if a washer with tubes into which the metal rods of palm tree branches are inserted is welded to the metal rod of the trunk. You can screw such a washer to a wooden trunk or simply drill it and insert scraps of metal tubes.

You can collect branches using the corks of the bottles themselves.

Or you can cut off the threaded necks and use a stapler. Or, inserting bottle leaves one by one, secure only the last one to the rod.

The video shows step by step production palm trees made from plastic bottles:

Mini palm tree made from plastic bottles, video

If you are not ready for a global implementation of the idea of ​​planting palm trees from plastic bottles, such as in the first photo, then you may like the minimalist idea.

To enlarge the picture, click on it.

We described the method for making the leaves of one of these homemade palm trees, and video instructions for making such a composition can help you in making it:

It is also interesting in one of the methods for making a barrel, which can be used in the production of more large palm tree for placement in the yard, and also the method of heat treatment of plastic, which we mentioned earlier.

Artificial coconuts, bananas and other palm fruits can be made from polystyrene foam, covered with paper and painted. If you paint them in several layers with acrylic paints for exterior use, they will be able to live outdoors for quite a long time.

And finally, one more video:

Dear readers, if you have any questions, please ask them using the form below. We will be glad to communicate with you;)

Creating a palm paradise on your site is simple and very exciting process, which can also include children. In this article we will try to give detailed description step by step instructions How to create a palm tree from plastic bottles with your own hands.

For this, we, of course, need bottles in brown and green tones. You can choose not to match - a variety of shades will give your palm trees a more natural look. You can also choose any bottle size from 1.5 to 2.5 liters.

Vote for the most successful, in your opinion, version of a palm tree made from plastic bottles (click on the picture to enlarge)

So, to create a palm tree trunk we need bottles in brown shades. To do this, we use a knife to cut the bottles crosswise almost in half, but the lower part should remain slightly larger than the upper part, the one with the neck. At the same time, we don’t throw anything away - all the cut off parts will be useful to us.

The top half of the bottle must be cut into 8 equal parts to the point where the narrowing of the bottle begins. And then we give each of these parts the shape of petals, or triangles, which must be opened in the form of a flower, making a fold at the base. The lower parts of the bottles are cut in the same way, however, first you need to make a hole in the middle of each of them the size of the neck. This can be done using a hot knife.

Let's begin by describing the process of obtaining foliage. To do this, we take bottles of green shades. Using a knife, cut off the neck and the very bottom of the bottle, where it curves. Then, starting from the bottom, cut the bottle into 3-4, if possible, equal parts. The number of cuts will depend on the size of the bottles and the palm tree itself. Before reaching the top of the bottle by about 2-3 cm, we stop the cuts.

Then you need to bring the foliage into proper shape. To do this, slightly round the lower parts of the resulting petals, and closer to the neck, on the contrary, narrow them. Then we straighten them along one plane.

To form foliage, each of the petals must be cut on both sides, leaving 1.5 - 2 cm in the middle. The cuts must be made obliquely, in the direction from the rounded sides to the narrowed middle. To add splendor, we unbend each resulting strip of foliage in the sequence: down, skip, up, skip.

Can be used as a rod plastic pipe or an iron pin of small diameter so that all parts of our palm tree can be inserted onto the base. The height of the palm will depend on you and, of course, on the number of bottles used.

The palm tree is assembled like this: we assemble all the finished parts of the trunk with the neck down, from the largest bottles to the smallest. When inserting the next part of the barrel, you need to rotate the petals so that they occupy the empty spaces of the previous part, i.e. in a checkerboard pattern. The very first part is attached to the pipe using tape.

Pay attention to this material -