When starting to renovate a house, you need to immediately solve a number of problems: think through the design, calculate the estimate, select materials. The same questions arise during renovation of the toilet.

If earlier tiles were almost universally used for wall decoration, today construction market offers everything more options cladding. And one of the most in demand today is plastic.

How to finish a toilet plastic panels, restroom design, the pros and cons of such coverage - we will consider all this in this article.

In contact with

What are PVC panels

PVC panels They are a hollow structure made of two layers of plastic connected by stiffening ribs. There are locks on the sides that are firmly connected to each other, remaining invisible in the finished finish. The result is perfectly flat surface.

Because the range of applications plastic sheathing is wide enough, there are many design options:

• Standard options lengths: 2.7 m, 3 m and 5.95 m. Thanks to this choice, you can finish large rooms without unnecessary joints.
• Width varies from 0.1 to 0.5 m. In this case, elements with the smallest width are produced as imitation wooden lining, so they have emphasized joints. How more material width, the less noticeable the seams.
• Thickness. The thicker the slab, the stronger it is considered. Therefore, for a ceiling where special strength is not needed, a sheet with a thickness of 5 to 8 mm is sufficient. For walls, slabs with a thickness of up to 10 mm and a large number of stiffeners are used. This allows you to maintain the integrity of the finish if someone leans on it or accidentally hits it.

In addition to the difference in dimensions, plastic materials for the toilet there are many decorative solutions.

Advantages of PVC panels for wall decoration

On the one side, special requirements To there is no wall cladding in the toilet, since there is no high humidity, as in the bathroom, or frequent pollution, as in the kitchen. Therefore the question arises: “ What to cover the toilet with?“After all, in this case it is not necessary to use expensive tiles. Plastic – suitable option, satisfying all practical and aesthetic requirements.

Advantages of PVC panels:

1. Variety of design solutions. Modern plastic is not limited to one modest coating; on the contrary, many colors and patterns, imitation of various textures will help create an unusual design.
2. Hygiene. Plastic does not absorb dirt and odors, it is easy to clean, and there is no need to use aggressive cleaning agents.
3. Economical. The price, even taking into account the necessary components, is lower than the cost of tiles.
4. Easy to install. To decorate walls with materials with your own hands, you do not need to have great experience V construction industry or a special expensive tool.

Important! Choosing wall materials for a toilet, you need to understand that plastic also has disadvantages, such as flammability or susceptibility to mechanical damage. However, basic caution will protect you from unpleasant consequences in the form of damaged cladding.

How to choose PVC panels

Since PVC panels- a product that is in demand and popular, some manufacturers, in an effort to make money, release low-quality products to the market. Therefore, you should approach the choice of finishing material responsibly so as not to become a victim of scammers. Otherwise, bathroom renovation with PVC panels will turn out to be an unpleasant surprise.

Choose quality materials simple tips will help:

Materials and tools required for installation

For high-quality and fruitful work above the wall decoration, you need to prepare in advance necessary materials and tools. A preliminary list of materials might look like this:

• Plastic panels for a bathroom based on required quantity with a reserve;
• Auxiliary and fastening materials: corners, baseboards, guides;
• Basis for lathing– wooden beam or metal profile;
• Wood processing composition, primer for walls;
• Fasteners: dowels, screws, staples;
• Glue for installation of plastic corners;
• Film or fabric for protection plumbing from pollution;
• Hammer, drill, construction stapler;
• Hammer;
• Pencil, tape measure, building level.

You always need to purchase materials with a small margin– up to 10-15%. If during work any part of the material is damaged, or it turns out that there was an error in the initial calculations, they will become good insurance. Moreover, if not taking care of a sufficient supply, may not be found similar material in the shop.

Installation procedure

So that the results of labor last time to please the owner, facing the toilet with plastic panels should begin with preparatory work. The first step is to remove any remaining old trim and paint. For this you will need spatula and small hammer.

Preparing the walls

Walls treated with a special primer with antiseptic properties. This will protect against the occurrence of fungus and mold in the future. Now you need to wait until the primer dries: about one hour.

Creating a wireframe

Next is made frame installation. If a wooden beam is chosen for the sheathing, it must be pre-treated with impregnation to protect it from moisture and rot. This step will extend the deadline cladding service for a long time.

It is advisable to do processing for fresh air , and bring the material into the house only after the composition has completely dried.

To create a sheathing, base bars are installed to the wall around the perimeter of the room: slightly above the floor and under the ceiling.

For strong fastening, the rail is applied to the surface and drilled. Wherein resulting hole should go 5-6 cm into the wall. Next, dowels are driven into it. There should be a distance of 30 to 50 cm between them.

Once installed upper and lower level of slats, the distance between them is measured, and another row of sheathing is attached exactly in the center. The same should be done with the remaining sections until there is a distance of up to 50 cm between the slats.

According to the same principle the frame is produced when finishing the ceiling with plastic materials.

Important! Knowing the expansion capabilities of wood, when installing the sheathing, you need to leave small gaps on the sides, i.e. the length of the bars should be a couple of centimeters less than the length of the wall.

Installation

Before as install PVC plates, a guide profile is attached to the ceiling and corners of the room. Installation is carried out to wooden blocks using a construction stapler. It is important to pay special attention to the installation of the first panel: it must be adjusted strictly according to level. The rest of the finishing fragments will be oriented specifically towards it. The comb of the first, and each subsequent one, the plates are fixed with brackets on a wooden slate.

The final stage

When toilet wall decoration plastic panels are completed, the stage of surface decoration begins. For this purpose they are used outer corners, since they are the most convenient in installation plan.

To fix the corner, you need to cover it with a layer of special glue for plastic, and press it tightly to the junction of the panels. The action must be fast and confident, since the setting time good glue is only a few seconds.

Skirting boards are attached similarly near the floor and ceiling. Excess glue can be easily wiped off with a soft cloth.

Lighting issue It is worth thinking about in advance, since to install spotlights, the lathing for plastic panels must be mounted 15 cm below the ceiling.

Color solutions

Now, knowing how to sheathe a toilet DIY plastic panels, you can start developing a design and choosing a color scheme.

Thanks to variety of decorative solutions in an assortment of plastic panels, create original design V toilet room won't be difficult. Therefore, when choosing materials you need to focus on design solution and your own taste preferences.

A universal solution monochromatic materials are considered that will fit into any interior and become a suitable background for other items.

In addition, one must take into account room dimensions– for a small room it is better to choose light shades, and for a spacious room, rich and dark colors are suitable.

For more originality and expressiveness You can choose panels with a pattern. The most popular are considered geometric patterns, abstractions, floral motifs.

Nautical themed decor(shells, sandy beaches and pictures of the underwater world) is suitable for finishing a combined bathroom.

The design looks impressive and expensive imitation of natural texture: wood, marble, stone. But when choosing such decor, it is important to ensure that the quality of the design is at a high level, otherwise the overall perception of the interior may be spoiled.

It’s not difficult to organize finishing a toilet with plastic panels yourself if you have at least minimal experience installation work. But first, it’s worth understanding the features of the material, the rules for installing the frame and other subtleties of the cladding. But, following the advice of experts, anyone can repair a bathroom on their own.

To decorate a toilet with panels yourself, it is enough to know the basic technological aspects. The special advantages of PVC panels can be attributed:

• convenient and simple installation that anyone can handle;
• low price, compared to other types of cladding, plastic finishing is much cheaper;
• during repairs, there is no need to level the walls, and this allows you to save money on building materials;
• plastic panels have good waterproofing, which means there is no need to worry about moisture;
• easy to clean, it will be enough to wipe the panels with a damp cloth from time to time;
• long service life.

It is worth noting that if one element breaks, the structure can be easily dismantled. Thanks to these positive qualities PVC panels are the leaders among all facing materials.

But despite a large number of advantages, the material has a number negative qualities, which include the following:

• flammability: when ignited, the panels release compounds harmful to the body;
• It is extremely difficult to work in small rooms, since there is no opportunity to turn around;
• are exposed to mechanical stress, even a slight blow can cause the bar to break or crack;
• conceals several centimeters of area, so that small room their use is not recommended.

Plastic panels are very light, they are quick and easy to install. The material is used for wall decoration and ceiling covering, so they can be used to hide electrical cables, ventilation pipes and defects in the form uneven walls, cracks.

Preparatory work

If the walls are smooth, then the material can be laid directly on the load-bearing surface. Although this option is extremely rare, so most often most of the time is spent on installing the frame. Do-it-yourself toilet decoration with plastic begins with the installation of the frame, for this you need:

1. First you need to remove old finishing to a concrete or brick base. Must be cleaned tiled cladding, if you do not remove the tiles, then over time they will fall off, but under the new cladding. If the walls are painted and the paint adheres firmly, then there is no need to beat it off, it will not interfere.
2. Inspect the surface for cracks; if there are any, they must be opened, cleaned of debris, and then filled with a repair compound. You can do this with cement mortar or use inexpensive tile adhesive.
3. To protect yourself from the appearance of bacteria or fungi under the panels, you need to treat the surface with any antiseptic. Experts recommend doing two impregnations with a time interval of 6 to 12 hours. During this period, the walls just have time to dry well.
4. If you plan to lay the sheets on the ceiling, then pre-tension the wiring for lighting fixtures. The cable is placed in special protective covers that will protect the wire from moisture. They are then fixed to the base ceiling plastic clamps or using wire hangers.

After the walls and ceilings have been prepared, the construction of the frame begins. For this you can use metal or wooden profiles.

For rooms with high humidity best to use wooden beams, which are pre-treated with an antiseptic. This option is much cheaper than a metal structure.

To mount the frame, you need to do the following:

• the bars on which the plastic panels will be attached are treated with antiseptic impregnation, then they need to be dried and cut into the required sizes;
• Now you should attach the block to the surface of the wall, drill holes in it using a drill and put marks through them, and then use a hammer drill to make sockets for fasteners;
• since the plastic panels will be laid vertically, then load-bearing structure must be mounted in a horizontal position, taking steps of 50 centimeters;
• It is best to lay the sheathing at the height of the knee, waist and shoulder, in which case the plastic sheets will not be damaged by awkward movement;
• plastic dowels are hammered into the made sockets, then wooden blocks must be attached to them and secured with locking screws, moreover, so that the cap is buried in the wood;
• now you need to attach several thick boards to the wall and secure them with anchors;
• after this, you need to mark on the drawing the exact location of the boards, since subsequently it will be possible to attach a mirror, bedside table or shelf to them;
• the ceiling frame is mounted according to the same scheme;
• to lay casings with electrical wiring in the beams, special grooves are cut required size so that the cable is not pinched.

To disguise sewer pipes, you need to install a vertical beam and fix it to the floor and ceiling using a metal corner. After this, install the sheathing under the plastic panels. In order to have access to the pipeline, it is necessary to mount wooden square, and then attach the inspection hatch to it. Installation of a metal profile is carried out according to the same scheme, but it is much more difficult to work with such material, so it is better for beginners to use wood.

Sheathing and finishing

After the frame is assembled, you can proceed directly to the sheathing. Since the bathroom area is usually small, installation will not take much time. To sheathe the structure, you must proceed according to the following scheme:

• the starting profile is placed on the corner, and it must be leveled using a building level, and then fixed with glue or self-tapping screws;
• a ceiling profile is attached along the entire perimeter, with the help of which vertical and horizontal elements will be connected;
• first wall panel it is necessary to trim in height, this gap will help ensure unhindered temperature deformation;
• Now you can insert an element into the starting profile and align it vertically;
• fix the sheet to the frame with self-tapping screws, and the upper edge is inserted into the groove of the plinth;
• the next sheet is inserted into the previous groove, panels are assembled to the next corner;
• the last sheet is cut lengthwise, if the plastic is soft, then this can be done using a painting knife, if the material is hard, then you can use a file with small teeth, the panel is inserted into the starting profile;
• The entire space of the bathroom is sheathed according to the same scheme.

At the very end, holes are cut for the built-in lamps and decorative skirting boards are installed, which mask the lower edge of the panels. All gaps and cracks are sealed with moisture-resistant silicone. At this point, the lining of the toilet with plastic panels is completed. Self-installation It’s not difficult if you follow the sequence of steps.

Repair is a necessary task, but not always pleasant. This is associated with financial waste, physical effort and some other inconveniences. However, everyone will agree that the end result is worth it. In addition, the materials from which the repairs are made play an important role. Today we will look at decorative finishing toilet.

The room is small, but very necessary. It has its own characteristics, including high humidity inside. This means that the finishing material must withstand such an environment. One of the excellent options is plastic panels.

What makes this material special? What are its advantages and disadvantages? How to decorate a toilet with plastic panels yourself? We will look at all this in this article. We will provide step by step instructions, and we will also see how to finish a toilet with plastic panels, video lessons.

Features of PVC products

What is good about this material? Let's start with the fact that among the many finishing materials plastic panels occupy their rightful place. And for the toilet they are simply ideal. Why can you say this? The toilet has its own characteristics. That is why durable, moisture-resistant materials are used for its finishing. Tiles are often purchased for this purpose. But its cost is much higher than the cost plastic products. The toilet itself is quite small, making the tiles difficult to work with.

Another thing is plastic elements. With practically the same characteristics, they are much cheaper and easier to work with. Finishing the toilet with plastic panels can be done with your own hands. Here are other features of the material that are important to consider:

If we talk about the disadvantages, they consist in the insufficient strength of the panels, combustion and their ability to fade. But, for a toilet, the second factor is not relevant, since usually there are no windows at all, or they are made very small. So the sun's rays cannot damage the material. And if used carefully, it will be difficult to damage the surface.

Options for finishing the toilet with plastic panels photo.

Immediately before finishing the walls, you need to purchase material. How to do it?

Choosing plastic panels for the toilet

To ensure that the work is not done in vain, and that the finish looks decent and is durable, it is important to choose the right materials. You can find a variety of products on store shelves, but how to choose them correctly? Let us immediately note that demand creates supply. And since the panels are popular, you can end up with an unscrupulous manufacturer. Define defective goods it can be difficult. What will help with this? Let's look at a few tips.

Thanks to these tips, you can save yourself from the possibility of buying low-quality Construction Materials. Right choice materials - this is already 50% of the work on high-quality finishing toilet. This is what it looks like correct finishing walls in the toilet with plastic panels in the photo.

Getting ready to install PVC panels

The first stage of work is preparation. If the panels have already been purchased, then it is time to take care of other tools and materials. Principle PVC installation panels resemble clapboard finishing. Therefore, the work will require the creation of a frame. It can be metal or wood. We recommend avoiding wooden ones, because the toilet is a damp room, wood can rot and quickly fail.

To create metal carcass required:

In addition, you can’t do your work without the following tools:

• screwdriver or drill driver;
• metal scissors;
• clamps, self-tapping screws or a stapler for fixing the panels to the frame;
• special profiles and skirting boards for plastic;
• tape measure, level, pencil;
• plastic hacksaw;
• metal spatula;
• stationery knife.

When everything is assembled, you can begin preparing the walls of the toilet.

Preparing the walls

To break, as they say, is not to build. The first task is to remove the old finish from the walls. The good news is that the toilet is small, so it won’t take much time. Use a spatula to remove the old finish. The work is simple, but time-consuming. Then the walls are cleaned of dust and dirt.

Note! To ensure that nothing disturbs you during your work, you should remove all excess from the toilet.

When the surface is prepared, you can begin to create a frame or sheathing on the wall. The peculiarity and advantage of this finishing method is that in the space under the slabs you can hide wiring or insulate a toilet. Let's look at step-by-step instructions for creating a metal frame.

We mount the metal frame

The main task is to make the frame even and correct, so you can’t do without marking and controlling the process with a level. Since the panels will be fastened in a vertical position, the frame for them is made in a horizontal position. The instructions for creating are as follows:

That's all, the frame for the walls is ready. Finishing a toilet with plastic panels (frame stage) do it yourself video.

Installation of plastic panels

Further work involves using plastic moldings. What are they needed for? PVC strips must be inserted into the appropriate grooves, this applies to the floor, ceiling and corners. There is a molding for each case. The photo shows exactly how to implement this in practice and what molding is needed in this or that case.

That's all, the walls are ready. To make it easier for you, you can view the following information: decorating the walls in the toilet with plastic panels video.

Here's what finishing a toilet with plastic panels looks like, photo.

Ceiling finishing with plastic panels

If everything is clear with the walls, then the ceiling is next. It is recommended to trim it with panels too. It will look harmonious. Moreover, if you have learned how to decorate walls with panels yourself, then there will be no problems with the ceiling. The principle of work here is the same. It all comes down to the following steps:

1. Markings on the wall.
2. Fixation of sheathing and other elements.
3. Installation ceiling molding around the entire perimeter.
4. Installation of plastic panels.

As for the ceiling, there are some nuances here. For example, you need to make appropriate holes in the slats for lamps. For the toilet it is better to use buildable ones Spotlights. To do this, markings are made in the appropriate place, and a hole is cut in the panel using a special crown attachment for a screwdriver. The work is not difficult. We have prepared visual video, how to complete the work from start to finish (installation on walls and ceilings). This may apply to the bathtub, but the principle of operation does not change. Finishing a toilet with plastic panels video.

Conclusion

Now your toilet is ready for full operation. The toilet renovation was done with minimal waste of money. As you can see, all the work is quite simple. If you try, the toilet will be ready in 1-2 days. Plastic panels are an excellent material that is easy to work with, it will last a long time, and there will be no problems with its operation. The toilet will look like new. And due to the fact that the surface of the products is glossy, this will visually increase small space in room. With such experience, you can successfully finish not only the toilet, but also the apartment as a whole. Such skills will be useful in life.

8479 0 0

How to install PVC panels for a toilet yourself, and why they are good

It just so happens that tiles traditionally reign in our bathrooms. There is nothing to say here; the cladding is certainly good and reliable. But such pleasure does not come cheap. Not counting the cost of the material itself, you often need to pay almost the same amount for installation, because not everyone can handle such work. But now there is an excellent alternative - PVC panels for the bathroom and toilet. Based on my own experience, then I will tell you why people love PVC panels so much and how to install this coating with your own hands in several options.

Why people choose PVC panels

I won't say that PVC sheathing toilet panels is the best and almost the only possible option, but still, such cladding has much more advantages than disadvantages, judge for yourself:

• Everyone knows that only wallpaper is lighter than plastic, therefore, any base will withstand such cladding. In this case, it doesn’t matter at all what kind of walls you have, concrete (including newfangled foam and aerated concrete) or wood. The plastic will fit perfectly both on the walls and on the ceiling;

• If you choose traditional frame installation, then you will not need to level the walls. Many people prefer not to even plaster. You can imagine how much the cost of the project is reduced;
• Polyvinyl chloride material is absolutely resistant to any humidity, plus modern models Fungus and mold do not grow; they are initially covered with an antiseptic. Although moisture resistance should not be confused with waterproofing, PVC cladding is exceptionally good decorative coating, waterproofing is something else and, for example, in a bathroom, it will need to be arranged separately even before installing the plastic;
• Caring for such panels is no more difficult than caring for tiles. A simple sponge and traditional detergent will suffice here;

• Modern plastic has a wide palette of colors and textures; such cladding can imitate most popular coatings, in which it is significantly superior to the same tile;
• And finally, self-finishing a toilet with PVC panels costs at least 3 – 5 times less than professional installation good tiles. Agree, it is difficult to argue with such an argument.

There are also negative aspects to this cladding, but they are quite controversial:

• So opponents immediately point out that the plastic burns and at the same time releases toxic compounds. It's true, but modern panels made from self-extinguishing material, from a cigarette or short circuit they can only melt; a strong fire is extremely unlikely. And if you are not going to barbecue or warm yourself by the fire in the toilet, then you have nothing to fear;

• Some say that finishing with your own hands requires serious preparation, but from my own experience I can tell you for sure, they are lying to you. If you are able to drill a hole in the wall with a hammer drill, and are not afraid of a screwdriver and a hacksaw, then you can handle it quite well, such work will not be a problem for you;
• The only one in my opinion real minus is a slight loss of usable space. The fact is that with frame installation you will actually lose at least 30 mm on each surface. Although we should not forget that there is also a frameless option. I will also talk about this technology.

Technology and installation options for PVC panels

Like any similar work, repairing a toilet with PVC panels is divided into several main stages. This is, first of all, the choice of material, preparation of the base and the actual installation itself.

Finishing the toilet with PVC panels begins only after the floors are equipped, plumbing and doors are installed. All major parts, for example, a sink or heavy wall cabinet, attached to the base.
The maximum you can hang on a plastic covering is small photo framed or light mirror. On the ceiling, such a panel can still support a built-in LED spotlight.

A few words about the choice of material

The external data of the coating is, of course, important, but most bathrooms in domestic apartments do not shine in size, so I recommend paying primary attention to the strength of the panel. If this does not play a special role on the ceiling, then thin plastic on the wall can easily be pushed through by accidentally leaning on it or touching it with your elbow.

When choosing panels, pay attention to the front side. If internal stiffening ribs are visible on it, then you are dealing with thin, low-quality material and you should not take it.

In general, PVC panels are for external and interior decoration, we are naturally interested in the second option. The width of such planks varies from 120 mm to 500 mm.

Now let's talk about the material for the frame. If you have had to install drywall and you know how to handle UD and CD profiles, then such a frame will be an almost ideal option.

For people who are far from such work and are faced with installing a frame for the first time, I recommend using wooden slats. Minimum size such slats are 20x25 mm. But if the loss of useful area of ​​10 mm does not play a big role for you, then it is better to mount a frame from a 30x30 mm bar.

Don't skimp on connecting fittings, various kinds corners, baseboards and fillets should be taken with a small margin. When cutting corners, it is very easy to make a mistake, and you definitely don’t want to run to the market for a new plank. Moreover, the price for such a product is quite affordable.

In addition to frames made of metal profiles and wooden blocks, such structures can be assembled from special guides with movable clamps. Such cladding is more expensive, but it is very easy to dismantle and reassemble if necessary.

Frame installation

First of all, remember that the frame guides are mounted perpendicular to the PVC facing strips. In wet rooms, such as a toilet with a bathtub, most often the panels are mounted vertically, respectively, the frame slats run horizontally. This is done so that water does not accumulate in the locks, but flows down along them.

As you understand, between plastic coated and with the wall we have a gap equal to the thickness of the frame planks. In the warm and damp room without drafts it is simply a resort for fungus and other similar vegetation. Therefore, even before starting work, the entire room needs to be coated with an antiseptic a couple of times.

There are now quite a few similar compounds on the market, with a waterproofing effect. Although if you are dealing with brick or classic concrete wall, then you can limit yourself to treating the surface with a solution two or three times copper sulfate, it's cheap and quite effective. Some people whiten it with lime; it dries well. But in both cases the result is quite decent.

Wood and aerated concrete must be covered with waterproofing primer deep penetration. Here it is better to use special compounds, they are different and all have instructions, so there is no point in writing about it.
Theoretically it can be painted oil paint, but it is not durable and such savings will cost more.

If the frame is made of wooden blocks, then they should also be well soaked with an antiseptic. Of course, you can spend money on special composition, but I prefer to do it simpler, I cover it with used machine oil a couple of times, it’s cheap and effective. Such slats will last for decades and nothing will happen to them.

You need to start installing the frame by installing vertical support rails around the perimeter in all corners. This is the main skeleton of the structure; the guide fittings will be attached to it, so they need to be mounted clearly and plumb. If the wall is very crooked, then wooden wedges are placed under the planks.

Fastening of any frame strips is carried out according to the standard scheme. First, a thin drill is used to make a row through holes in the plank, so that the drill leaves a mark on the wall. After this, the plank is removed, and holes for plastic dowels are drilled in the designated places. When everything is ready, all you have to do is insert the dowels and secure the bar with self-tapping screws.

There's one here small nuance. Vertical guides should not rest against the floor and ceiling; a gap of about 5 mm is left between them. As a rule, during installation, scraps of the same plastic are inserted from above and below, and after fixing with self-tapping screws, they are pulled out. It is advisable to drill out an underlay on the bar for the screws, so that the cap is hidden in the bar.

With the installation of horizontal guides everything is a little simpler. They are also fixed to the walls with self-tapping screws, but in order for the bars to stand at the same level (meaning the case with very curved walls), they are screwed to the ends of the side vertical supports.

This can be done using metal corners or simply by driving a self-tapping screw from the side at an angle of 45º into both planks at once. On curved walls, to prevent the planks from bending, wedges are placed under them.

The horizontal guides, to which the PVC panels will actually be attached, are installed in increments of 30 - 50 cm, here everything depends on the strength of the panels themselves.

Often in city apartments all communications, that is, sewer riser, water supply and so on, run along the back wall of the toilet. So, PVC cladding provides an excellent opportunity to hide all this “beauty”. In this case, two vertical support rails are mounted not at the rear corners, but in front of the pipe package. The horizontal sheathing is already attached and sewn on them using corners.

And to provide access to communications, hinged doors from or OSB boards. By the way, these doors can also be covered with plastic, as a result they will blend into the general background.

Paneling

Sheathing PVC panels toilet, or rather fixing them on wooden frame can be performed in different ways. Some craftsmen recommend using small nails with wide heads for this. Theoretically this is possible, there is no error here.

But there is one important nuance. You will have to hammer these nails into a narrow mounting strip on the edge of the panel, and if you miss once and hit the panel itself with a hammer, it will crack and will need to be replaced.

Now there is one convenient device like a construction stapler. Plastic mounting plate at the edge of the panel itself is thin and can be easily pierced by the sharp legs of metal brackets.

The price for this same stapler is quite reasonable, plus it can come in handy more than once on the farm. And if you are absolutely sure that you will not have to disassemble in the foreseeable future plastic lining, feel free to mount it on the brackets.

But personally, I prefer to fasten the panels with small self-tapping screws. True, for this it is advisable to have a normal screwdriver; screwing such a number of screws with a screwdriver will tire your hand.

This method is also good because it doesn’t matter what kind of frame you have, wooden or assembled from metal profiles. It’s just that one type of screw is used for wood, and another for metal.

The technology for installing PVC panels is extremely simple. First, fittings are attached to the guides, that is, corners and plinths. This is an important stage, everything here should be as accurate as possible. The grooves in all guides have a depth of at least 10 mm, this must be taken into account when cutting the planks.

In my opinion, for fans of PVC panels, it is best to cut them using a hacksaw. Some craftsmen cut with a sharp shoe knife or even metal scissors; this is possible, but in order not to spoil the edge you will need to practice.

Polyvinyl chloride is prone to thermal deformation, so the strip itself is cut taking into account the damper gap to compensate for expansion. Simply put, you need to measure approximately 5 mm less than the maximum length dimension.

Then everything is simple. The bar is slightly bent, inserted into the lower and upper fittings guides, and then advanced until it enters the side groove of the starting corner.

Now you need to secure the panel to each horizontal rail using a screw or bracket.

The plastic panel has a tongue on one side and a groove on the other. The tenon of the first panel should be hidden in the groove of the fittings. The tenon of the next panel is inserted into the groove of the previous one, after which it is fixed on the guides. And so on until you have sewn up the entire wall. Particular attention should be paid to the outer panel. In the vast majority of cases, it will need to be trimmed along its entire length. It is cut approximately 5 mm narrower than maximum distance

between the grooves of the previous panel and the fittings.

After that, insert it into the guides and first push it all the way into the groove of the fittings, and when it goes in, slide it back until it completely fits into the groove of the previous panel. As you remember, the grooves on the fittings are much deeper and the difference in size will not be noticeable.

It is inconvenient to insert the outer cut strip directly into the upper, lower and side grooves. To prevent the edges of these grooves from bending or, worse, cracking, I recommend bending them in advance using wide metal spatulas, although you will need an assistant here.

I already mentioned above that there is also mounting on clamps. So, here you will need special guides. They are equipped with two grooves into which clamps are inserted and move along them as if on rails.

The clamp itself is a flat metal bracket with a small “tongue”. When you insert the strip into the grooves and push it all the way, the clamp is adjusted from behind and presses the mounting strip with its tongue. No screws or staples for you, everything is simple and beautiful.

Instructions for covering the ceiling PVC toilet panels are not much different from the technology of wall cladding. Unless you first need to lay electrical cable under the lighting, and hide it in a corrugated metal sleeve. Naturally, when installing the frame, you will need to take into account the depth of the built-in ceiling soffit. The hole for it is cut with a special crown using an electric drill.

Subtleties of frameless installation

PVC panels for bathrooms and toilets can be mounted without a frame, directly on the walls and ceiling, only for this purpose smooth curvatures on the plane should not exceed 3 mm, we are not talking about any potholes or distortions at all. The technology in this case is much more accessible - the panels and fittings are simply glued to the walls and ceiling.

As a rule, so-called “Liquid nails” are used as the main adhesive; this is a fairly common construction adhesive with an optimal price-quality ratio.

But working with him has one peculiarity. First, glue is applied to the wall and the panel is applied to it. After which it is torn off and left for 3 - 4 minutes for weathering, and only after this the PVC plank is finally glued.

I have a real-life incident on this topic that will be useful to you. One of my friends, having bought an apartment on the secondary market, inherited services from the previous owners, taxed tiles. The tiles were good, but very old and ugly. There was neither the desire nor the means to knock it down and lay down a new one, and the dimensions of the premises were more than modest; frame installation would have made them absolutely miniature.

The man did it simply. He thoroughly washed and degreased the tiles, then cut PVC panels and glued them to the tiles with double-sided construction tape. He used 3 fixing strips on a 250 mm wide panel, but this is not a dogma; you can glue it in different ways.

When funds became available, and it came to expensive luxury repairs and redevelopment, tearing off this plastic was very problematic. So keep in mind that this option also has a right to exist.

Conclusion

If you want to express gratitude, add a clarification or objection, or ask the author something - add a comment or say thank you!

For some reason, when they talk about renovating an apartment, they first of all mean the living room, bedroom, or kitchen and bath. And they forget about the toilet. But there is also a need high-quality repairs. There are no such problems with this room as where there is constant humidity, or with the kitchen where there is smell and fumes from cooking. Toilet repairs are quite easy to do even on your own. You just need to choose the material with which the finishing will be done.

You can opt for plastic panels. And what? The selection is simply wonderful. After all, it costs about half as much as tiling. And this is a significant saving. In addition, this material looks great and is very hygienic. Which is important for this room. After all, plastic panels are very easy to wash with any suitable detergents.

What is a plastic panel

There was a time when such panels were used for European-quality renovations. This time has already passed, and such material is no longer perceived as something special. What is a plastic panel? This is a strip that is made of polyvinyl chloride (PVC). But simply, from ordinary plastic. It is released different sizes. Plus it cuts easily.

Its advantages:

• Cheap material. There are no special costs required for its purchase and installation.
• Hygienic, easy to clean.
• you can do it on your own.
• Very big choice various colors. In this regard, you can decorate the interior as you please.

Disadvantages usually include the presence of a plastic odor and the possibility of mechanical damage. To which we can answer that the smell of plastic in the toilet is still better than any other. As for mechanical damage, rarely does anyone enter the toilet with an ax in their hands.

Tools and installation sequence

For installation are used following materials and tools:

• wooden blocks;
• building level;
• screwdriver;
• plastic panels;
• screws, nails or glue.

First, wooden blocks are placed on the walls of the toilet. If the plastic panels are positioned vertically, then the bars are packed parallel to the floor. If it is horizontal, then the bars are packed perpendicularly. The bars must be set according to construction level. This determines how evenly the panels will be positioned.

Installation of the frame on walls made of metal profiles

When planning how they will be, you need to take into account that their vertical arrangement will visually make the room taller. And the horizontal one is wider.

Profile frame on the ceiling

The bars can be attached to the walls with dowels or self-tapping screws. If using self-tapping screws, then you need to drill holes and drive plastic chips into them. Wooden blocks must be well dried so that they do not warp later. After all, this could ruin the whole work.

Frame made of wooden blocks

The distance between the sheathing bars is usually 40-50 cm. If you plan to hang shelves or cabinets, then the sheathing bars are attached more often, taking into account the fastening of the shelves. This must be provided for in advance.

An alternative method is to attach the panels with glue.

Sequence of work

Let's assume that the panels are mounted vertically, since this is the most common option. First, the first strip of plastic is attached to the corner. This is the starting line, so to speak. The next strip is inserted into it with the narrow fastening side and secured with nails or self-tapping screws. The next panel is again inserted with the narrow fastening side. And so on until all the panels are secured. Special plastic corners are attached to the top and bottom, which can be purchased together with. The same corners can be fixed in the corners. There is nothing complicated about the installation work. It is somewhat reminiscent of a construction kit.

Video: installation of plastic panels

Toilet design with panels (photo)

Depending on the chosen design, the panels can be positioned so that they cover the wall by one quarter, half or completely, up to the ceiling. If the plastic does not reach the ceiling, then the remaining part of the wall needs to be painted or wallpapered. If it is wallpaper, then it should be washable so that it can be wiped with a damp cloth when cleaning the toilet. You can paint it water-based paint, adding the appropriate tint to give the desired color.

The ceiling in the toilet can also be decorated with plastic panels. no different from mounting it on the walls. It is only recommended to fill the sheathing a little more often. The distance between the bars should be 30-40 cm. Decorating the ceiling with plastic panels is also beneficial because lamps can be built in. To do this, you need to plan the wiring installation in advance.

It must be said that plastic panels do not necessarily need to be attached to nails or screws. Fastening can also be done using glue.

Panel fastening methods

For decoration, you can choose with a three-dimensional image.